Interested in learning more, or looking for welding automation? Please fill out the form below to get started. [Or, skip to read more]
Wondering if something like this would work for your process?
This robotic welding system was designed to assist a manufacturer of fuel cells and has the ability to handle variable parts and tanks of different sizes and shapes. So, whether you have a dedicated line of fuel tanks, water heaters, or you're building propane tanks, this system has the ability to be modified to meet your needs by simply changing out the tooling.
Other industries we serve include:
Let's Start with Safety:
Eliminating hazards and elements that put people at risk are all important considerations for automation systems today. Talking through the safest way to manufacture a part not only helps to set the foundation for the system design, but we have found it also helps lead to the most cost-effective system design as well.
Safety is always an intrinsic part of the design and safety features are built-in alongside the other components. In a synchronized robotic system like this one, the potential for harm is greater because of the inherent nature of servo motors. So, it is important to create safeguards that help prevent anyone from being in the path of uncontrolled motion or pre-programmed motions. A lot of these newer robotic welding systems also have reduced fumes due to fewer alloying ingredients being vaporized by the welding arc, which leads to a safer shop environment but we also want to minimize the potential hazards associated with welding.
In addition to some of the obvious standard practices of integrated estops and safety PLCs, here are some examples of how we helped eliminate the risks with this system:
Part Positioning:
Let's look at the two sides to this system - the part loading/positioning side and the welding side.
On the part loading of this system, there is a pneumatic lift table that supports and holds the fuel cell. The end caps are introduced and then held in place with vacuum assist on a tooling plate specifically designed for a particular tank or vessel.
There are two synchronized headstocks here to assist during assembly and later for the robotic welding.
The operator loads the tank and end caps onto the table, presses ‘go’ on the operating station and the sequence cycle begins with the headstocks compressing so the end caps are fitted. The drop door comes down and the loaded tank is rotated to the back half of the system where the robotic welding will commence.
Welding Robots - Laser Seam Tracking
The second half of this system is where the welding takes place. There are two synchronized robots that are tasked with this operation. Each robot is equipped with seam tracking.
The Seam Tracking sensor technology is mounted parallel to each robot weld torch. The sensors are capable of precisely following the weld joint in combination with the headstock motion, Fronius weld equipment, and Kuka robots. These sensors send feedback to the weld equipment based on material and joint conditions to make process adjustments.
The primary purpose of seam tracking is to ensure that the torch is in the optimum position to deliver the welding wire to the joint, including the height and centering of wire in the gap.
Using the information it reads, the laser seam tracking technology will automatically make the subtle torch attitude adjustments required to ensure the best possible weld can be produced for that weld joint profile.
Welding Robots - Adaptive Fill
Not only does this robotic welding system have seam tracking, with is fairly common, but it also is equipped to perform adaptive fill welding.
Adaptive fill allows for the correct welding process to be deployed to address the variability seen by the seam tracking for gap and height mismatch of the materials in a particular joint to be welded. It does this in a way that is just about as close to AI as you can get. Without the aid of any human intervention, pre-determined weld procedures are called out by the robot to address the anomalies in the joint.
Things like increasing amperage and wire feed, increasing weave, or motion of the torch to span the gap, slowing down or increasing the travel speed of the robots, or even addressing the speed of the rotation speed of the headstocks are all choreography into an elaborate program to take advantage of the modern technology available in today’s power supplies.
In addition to addressing gap control, which can be a challenge on most automated systems, other benefits of using adaptive fill include fewer stop-starts and less need for rework or human intervention. The system is much more capable of making the appropriate changes to maintain a good quality weld on all parts introduced to the system.(For more on robotic welding visit: robotic welding)
Tool Changer & Reaming Station
This system also includes the automatic tool change mounts on either side of the robots and an automated torch reaming station in the center, where, based on preprogrammed instructions, the torch head moves to have its nozzle reamed and wire trimmed. Increasing the flexibility of the system and minimizing the need for human interaction, truly automating that needs to be automated.
What about Production Monitoring?
This system is also equipped with the ability to turn on IRCOpulse, a subscription-based production monitoring package providing data insights and key performance indicator information to customers. The system can provide information about machine performance, downtime events, production statistics, throughput, efficiencies, and more. The collected data is accessed on a cloud database and automatically shows real-time connection to the system via interactive reports on things such as production output, cycle times, downtime events, maintenance, and more.
Stay tuned to our website to learn more about IRCOpulse - our answer to your Industry 4.0 questions.
Contact Us & Related Content
For more information about IRCO Automation's automated welding solutions, visit the Welding Automation page on our website.
Connect with our team by sending us an email at: info@ircoautomation.com
Looking to learn more? See the following Resources: